NOx Sensor A0101531728

BG 201033 (OE A0101531728): function on the vehicle

NOx Sensor A0101531728 is supplied by BEST GROWTH under part number 201033, cross-referenced to OE A0101531728, as a direct-fit aftermarket nox sensors. In service it supplies the emissions-monitoring value the OBD system uses to decide whether the SCR stage is still working within its legal window. A drifting cell triggers inducement long before the catalyst itself is worn out.

BG 201033 is built to the position defined by its OE application on a 24V electrical system in truck service on the platform from Mercedes-Benz. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Because the sensor carries its own control module, most "sensor" faults are really bus, supply or ground faults at the connector — the electrical side is worth ten minutes before the part is ordered.

Fitment for Mercedes-Benz and OE cross reference

BG 201033 replaces 2 OE references: A0101531728 and 5WK9 7332, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201033 includes Mercedes-Benz, typically on Actros OM471 LA 2013-. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by A0101531728 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing A0101531728

These complaints bring a vehicle in with the Mercedes-Benz nox sensors under suspicion. None of them prove BG 201033 has failed on its own, which is why the checks below matter before a replacement is ordered.

• torque derate or speed inducement with a full, in-spec DEF tank
• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running
• upstream and downstream values reading almost identically under load

Checks before fitting BG 201033

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Verify DEF concentration with a refractometer before blaming the measuring cell.
• Check for a pending software or parameter update for the sensor control module on that platform.
• After fitting, run the manufacturer's adaptation or relearn so stored efficiency counters reset.
• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.
• Confirm supply voltage, ground quality and bus termination before condemning the sensor module.

Quality, packaging and ordering 201033

BG 201033 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 24V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE A0101531728 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201033 replace OE A0101531728?

Yes. BG 201033 is listed against A0101531728 and 5WK9 7332. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201033 fit?

Recorded coverage includes Mercedes-Benz. It is supplied as a direct-fit aftermarket nox sensors on 24V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201033.