NOx Sensor 2429860 SNS0061H

BG 990514 (OE 2429860 SNS0061H): function on the vehicle

NOx Sensor 2429860 SNS0061H is supplied by BEST GROWTH under part number 990514, cross-referenced to OE 2429860 SNS0061H, as a direct-fit aftermarket nox sensors. In service it measures nitrogen-oxide concentration and residual oxygen in the exhaust stream and reports both values to the aftertreatment controller over the vehicle data bus. Upstream and downstream readings together set DEF dosing quantity and score SCR conversion efficiency.

BG 990514 is built to the position defined by its OE application on a 24V electrical system in truck service on the platform from DAF. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

The measuring cell is consumable. Soot loading, silicone contamination and repeated thermal shock all shorten its life, which is why a sensor can drift for months before it sets a hard code.

Fitment for DAF and OE cross reference

BG 990514 replaces 1 OE reference: 2429860 SNS0061H. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 990514 includes DAF, typically on CF / XF Euro 6. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Quote the number printed on your part with the engine code when you enquire; a single-reference part is the most common source of ordering errors when a platform received a mid-life update.

Symptoms that lead to replacing 2429860 SNS0061H

These complaints bring a vehicle in with the DAF nox sensors under suspicion. None of them prove BG 990514 has failed on its own, which is why the checks below matter before a replacement is ordered.

• DEF over-consumption with no visible leak
• torque derate or speed inducement with a full, in-spec DEF tank
• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running

Checks before fitting BG 990514

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.
• Confirm supply voltage, ground quality and bus termination before condemning the sensor module.
• Inspect the harness for heat damage and the connector for moisture and green corrosion.
• Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.
• Read the sensor's own dew-point release time — a cell that never heats is a supply or module fault.

Quality, packaging and ordering 990514

BG 990514 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 24V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 2429860 SNS0061H or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 990514 replace OE 2429860 SNS0061H?

Yes. BG 990514 is listed against 2429860 SNS0061H. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 990514 fit?

Recorded coverage includes DAF. It is supplied as a direct-fit aftermarket nox sensors on 24V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 990514.