Does BG 201058 replace OE A000 905 70 00?

Yes. BG 201058 is listed against A000 905 70 00 and 5WK9 6682A. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201058 fit?

Recorded coverage includes Mercedes-Benz. It is supplied as a direct-fit aftermarket nox sensors on 12V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201058.

201058

NOx Sensor A000 905 70 00

BG NOx sensor for Mercedes-Benz E-Class W212 350d / S-Class 350d, OE A000 905 70 00 / 5WK9 6682A, 12V urea/SCR system.

BG Part Number: 201058
Category: NOx Sensors
Application: E-Class W212 350d / S-Class 350d
Voltage: 12V
Vehicle Manufacturer: Mercedes-Benz

Applications

Passenger Car

OE Cross References

A000 905 70 00
5WK9 6682A· cross

Review Inquiry Basket Ask a Technical Question

Product Description

This BG NOx (nitrogen oxide) sensor is designed for the urea/AdBlue-based SCR (Selective Catalytic Reduction) emissions system on Mercedes-Benz E-Class W212 350d / S-Class 350d. It is a direct-fit replacement for OE reference A000 905 70 00 / cross reference 5WK9 6682A. Rated for 12V electrical systems. The sensor provides accurate real-time NOx measurement for precise urea dosing control, helping maintain stable SCR performance and compliance with diesel emission standards.

Vehicle manufacturer names, logos and OE reference numbers are used for identification and compatibility purposes only. BEST GROWTH products are independent aftermarket products and are not manufactured, sponsored or endorsed by the respective vehicle manufacturers.

BG 201058 (OE A000 905 70 00): function on the vehicle

NOx Sensor A000 905 70 00 is supplied by BEST GROWTH under part number 201058, cross-referenced to OE A000 905 70 00, as a direct-fit aftermarket nox sensors. In service it acts as the closed-loop feedback element of the SCR circuit: it tells the controller how much NOx is still leaving the catalyst, so dosing is trimmed up or down instead of running to a fixed map.

BG 201058 is built to the position defined by its OE application on a 12V electrical system in passenger car service on the platform from Mercedes-Benz. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Cable length and connector keying are part of the specification. A cell with correct electrical output but the wrong lead length will not route to the OE bracket.

Fitment for Mercedes-Benz and OE cross reference

BG 201058 replaces 2 OE references: A000 905 70 00 and 5WK9 6682A, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201058 includes Mercedes-Benz, typically on E-Class W212 350d / S-Class 350d. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by A000 905 70 00 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing A000 905 70 00

These complaints bring a vehicle in with the Mercedes-Benz nox sensors under suspicion. None of them prove BG 201058 has failed on its own, which is why the checks below matter before a replacement is ordered.

dosing shut-down after a few minutes of steady-state running
upstream and downstream values reading almost identically under load
intermittent fault that clears after the engine cools and returns when hot
SCR efficiency below threshold or NOx-signal-implausible fault codes
DEF over-consumption with no visible leak

Checks before fitting BG 201058

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

Inspect the harness for heat damage and the connector for moisture and green corrosion.
Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.
Read the sensor's own dew-point release time — a cell that never heats is a supply or module fault.
Verify DEF concentration with a refractometer before blaming the measuring cell.
Check for a pending software or parameter update for the sensor control module on that platform.

Quality, packaging and ordering 201058

BG 201058 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 12V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE A000 905 70 00 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201058 replace OE A000 905 70 00?: Yes. BG 201058 is listed against A000 905 70 00 and 5WK9 6682A. Confirm the number printed on the removed part and any manufacturer supersession before ordering.
Which vehicles does BG 201058 fit?: Recorded coverage includes Mercedes-Benz. It is supplied as a direct-fit aftermarket nox sensors on 12V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.
Does this fault code always mean the nox sensors has failed?: No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201058.