NOx Sensor A000 905 35 03

BG 201061 (OE A000 905 35 03): function on the vehicle

NOx Sensor A000 905 35 03 is supplied by BEST GROWTH under part number 201061, cross-referenced to OE A000 905 35 03, as a direct-fit aftermarket nox sensors. In service it acts as the closed-loop feedback element of the SCR circuit: it tells the controller how much NOx is still leaving the catalyst, so dosing is trimmed up or down instead of running to a fixed map.

BG 201061 is built to the position defined by its OE application on a 12V electrical system in passenger car service on the platform from Mercedes-Benz. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Cable length and connector keying are part of the specification. A cell with correct electrical output but the wrong lead length will not route to the OE bracket.

Fitment for Mercedes-Benz and OE cross reference

BG 201061 replaces 2 OE references: A000 905 35 03 and 5WK9 6682C 5WK9 6682D 5WK96682B/C/D, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201061 includes Mercedes-Benz, typically on ML250 / ML350 / ML400 / GL320 / GL350 / GLE300d / GLS350d. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by A000 905 35 03 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing A000 905 35 03

These complaints bring a vehicle in with the Mercedes-Benz nox sensors under suspicion. None of them prove BG 201061 has failed on its own, which is why the checks below matter before a replacement is ordered.

• intermittent fault that clears after the engine cools and returns when hot
• SCR efficiency below threshold or NOx-signal-implausible fault codes
• DEF over-consumption with no visible leak
• torque derate or speed inducement with a full, in-spec DEF tank
• no communication with the sensor control module after a cold start

Checks before fitting BG 201061

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Inspect the harness for heat damage and the connector for moisture and green corrosion.
• Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.
• Read the sensor's own dew-point release time — a cell that never heats is a supply or module fault.
• Verify DEF concentration with a refractometer before blaming the measuring cell.
• Check for a pending software or parameter update for the sensor control module on that platform.

Quality, packaging and ordering 201061

BG 201061 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 12V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE A000 905 35 03 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201061 replace OE A000 905 35 03?

Yes. BG 201061 is listed against A000 905 35 03 and 5WK9 6682C 5WK9 6682D 5WK96682B/C/D. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201061 fit?

Recorded coverage includes Mercedes-Benz. It is supplied as a direct-fit aftermarket nox sensors on 12V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201061.