NOx Sensor A000 905 29 09
201212

NOx Sensor A000 905 29 09

BG NOx sensor for Mercedes-Benz Sprinter / Vito, OE A000 905 29 09, 12V urea/SCR system.

BG Part Number
201212
Category
NOx Sensors
Application
Sprinter / Vito
Voltage
12V
Vehicle Manufacturer
Mercedes-Benz
OE Cross References
  • A000 905 29 09

Product Description

This BG NOx (nitrogen oxide) sensor is designed for the urea/AdBlue-based SCR (Selective Catalytic Reduction) emissions system on Mercedes-Benz Sprinter / Vito. It is a direct-fit replacement for OE reference A000 905 29 09. Rated for 12V electrical systems. The sensor provides accurate real-time NOx measurement for precise urea dosing control, helping maintain stable SCR performance and compliance with diesel emission standards.

Vehicle manufacturer names, logos and OE reference numbers are used for identification and compatibility purposes only. BEST GROWTH products are independent aftermarket products and are not manufactured, sponsored or endorsed by the respective vehicle manufacturers.

BG 201212 (OE A000 905 29 09): function on the vehicle

NOx Sensor A000 905 29 09 is supplied by BEST GROWTH under part number 201212, cross-referenced to OE A000 905 29 09, as a direct-fit aftermarket nox sensors. In service it acts as the closed-loop feedback element of the SCR circuit: it tells the controller how much NOx is still leaving the catalyst, so dosing is trimmed up or down instead of running to a fixed map.

BG 201212 is built to the position defined by its OE application on a 12V electrical system in light commercial vehicle service on the platform from Mercedes-Benz. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Cable length and connector keying are part of the specification. A cell with correct electrical output but the wrong lead length will not route to the OE bracket.

Fitment for Mercedes-Benz and OE cross reference

BG 201212 replaces 1 OE reference: A000 905 29 09. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201212 includes Mercedes-Benz, typically on Sprinter / Vito. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Quote the number printed on your part with the engine code when you enquire; a single-reference part is the most common source of ordering errors when a platform received a mid-life update.

Symptoms that lead to replacing A000 905 29 09

These complaints bring a vehicle in with the Mercedes-Benz nox sensors under suspicion. None of them prove BG 201212 has failed on its own, which is why the checks below matter before a replacement is ordered.

  • dosing shut-down after a few minutes of steady-state running
  • upstream and downstream values reading almost identically under load
  • intermittent fault that clears after the engine cools and returns when hot
  • SCR efficiency below threshold or NOx-signal-implausible fault codes
  • DEF over-consumption with no visible leak

Checks before fitting BG 201212

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

  • Inspect the harness for heat damage and the connector for moisture and green corrosion.
  • Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.
  • Read the sensor's own dew-point release time — a cell that never heats is a supply or module fault.
  • Verify DEF concentration with a refractometer before blaming the measuring cell.
  • Check for a pending software or parameter update for the sensor control module on that platform.

Quality, packaging and ordering 201212

BG 201212 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 12V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE A000 905 29 09 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201212 replace OE A000 905 29 09?
Yes. BG 201212 is listed against A000 905 29 09. Confirm the number printed on the removed part and any manufacturer supersession before ordering.
Which vehicles does BG 201212 fit?
Recorded coverage includes Mercedes-Benz. It is supplied as a direct-fit aftermarket nox sensors on 12V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.
Does this fault code always mean the nox sensors has failed?
No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201212.

Related References

WhatsApp