NOx Sensor 9821120980

BG 201700 (OE 9821120980): function on the vehicle

NOx Sensor 9821120980 is supplied by BEST GROWTH under part number 201700, cross-referenced to OE 9821120980, as a direct-fit aftermarket nox sensors. In service it acts as the closed-loop feedback element of the SCR circuit: it tells the controller how much NOx is still leaving the catalyst, so dosing is trimmed up or down instead of running to a fixed map.

BG 201700 is built to the position defined by its OE application on a 12V electrical system in passenger car service on platforms from Peugeot, Citroën and Renault. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Cable length and connector keying are part of the specification. A cell with correct electrical output but the wrong lead length will not route to the OE bracket.

Fitment for Peugeot, Citroën and Renault and OE cross reference

BG 201700 replaces 1 OE reference: 9821120980. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201700 includes Peugeot, Citroën and Renault, typically on C3 / DS3 1.6 / 2.0. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Quote the number printed on your part with the engine code when you enquire; a single-reference part is the most common source of ordering errors when a platform received a mid-life update.

Symptoms that lead to replacing 9821120980

These complaints bring a vehicle in with the Peugeot and Citroën nox sensors under suspicion. None of them prove BG 201700 has failed on its own, which is why the checks below matter before a replacement is ordered.

• DEF over-consumption with no visible leak
• torque derate or speed inducement with a full, in-spec DEF tank
• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running

Checks before fitting BG 201700

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Check for a pending software or parameter update for the sensor control module on that platform.
• After fitting, run the manufacturer's adaptation or relearn so stored efficiency counters reset.
• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.
• Confirm supply voltage, ground quality and bus termination before condemning the sensor module.
• Inspect the harness for heat damage and the connector for moisture and green corrosion.

Quality, packaging and ordering 201700

BG 201700 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 12V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 9821120980 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201700 replace OE 9821120980?

Yes. BG 201700 is listed against 9821120980. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201700 fit?

Recorded coverage includes Peugeot, Citroën and Renault. It is supplied as a direct-fit aftermarket nox sensors on 12V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201700.