NOx Sensor 5801754014

BG 201153 (OE 5801627703): function on the vehicle

NOx Sensor 5801754014 is supplied by BEST GROWTH under part number 201153, cross-referenced to OE 5801627703, as a direct-fit aftermarket nox sensors. In service it acts as the closed-loop feedback element of the SCR circuit: it tells the controller how much NOx is still leaving the catalyst, so dosing is trimmed up or down instead of running to a fixed map.

BG 201153 is built to the position defined by its OE application on a 24V electrical system in truck service on the platform from IVECO. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

The measuring cell is consumable. Soot loading, silicone contamination and repeated thermal shock all shorten its life, which is why a sensor can drift for months before it sets a hard code.

Fitment for IVECO and OE cross reference

BG 201153 replaces 4 OE references: 5801627703, 5801754014, 5WK9 6775 and 5WK9 6775A, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201153 includes IVECO, typically on Stralis / EuroCargo / Trakker / X-Way. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by 5801627703 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing 5801627703

These complaints bring a vehicle in with the IVECO nox sensors under suspicion. None of them prove BG 201153 has failed on its own, which is why the checks below matter before a replacement is ordered.

• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running
• upstream and downstream values reading almost identically under load
• intermittent fault that clears after the engine cools and returns when hot

Checks before fitting BG 201153

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Check for a pending software or parameter update for the sensor control module on that platform.
• After fitting, run the manufacturer's adaptation or relearn so stored efficiency counters reset.
• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.
• Confirm supply voltage, ground quality and bus termination before condemning the sensor module.
• Inspect the harness for heat damage and the connector for moisture and green corrosion.

Quality, packaging and ordering 201153

BG 201153 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 24V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 5801627703 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201153 replace OE 5801627703?

Yes. BG 201153 is listed against 5801627703, 5801754014, 5WK9 6775 and 5WK9 6775A. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201153 fit?

Recorded coverage includes IVECO. It is supplied as a direct-fit aftermarket nox sensors on 24V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201153.