NOx Sensor 51.15408-0015

BG 201141 (OE 51.15408-0015): function on the vehicle

NOx Sensor 51.15408-0015 is supplied by BEST GROWTH under part number 201141, cross-referenced to OE 51.15408-0015, as a direct-fit aftermarket nox sensors. In service it runs a heated zirconia measuring cell inside its own sensor control module, converts the raw cell current into a NOx value in ppm, and publishes it on the bus. The engine controller cannot calculate dosing quantity or conversion efficiency without a plausible signal from it.

BG 201141 is built to the position defined by its OE application on a 24V electrical system in truck service on the platform from MAN. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Fitting position matters as much as the part number: upstream and downstream references often share a housing but carry different calibration data and cable lengths.

Fitment for MAN and OE cross reference

BG 201141 replaces 3 OE references: 51.15408-0015, 5WK9 6618D and 5115408-0015 51.15408-0013 5115408-0013, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201141 includes MAN, typically on TGX / TGA / TGL / TGM 2000-2013. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by 51.15408-0015 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing 51.15408-0015

These complaints bring a vehicle in with the MAN nox sensors under suspicion. None of them prove BG 201141 has failed on its own, which is why the checks below matter before a replacement is ordered.

• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running
• upstream and downstream values reading almost identically under load
• intermittent fault that clears after the engine cools and returns when hot
• SCR efficiency below threshold or NOx-signal-implausible fault codes

Checks before fitting BG 201141

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• After fitting, run the manufacturer's adaptation or relearn so stored efficiency counters reset.
• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.
• Confirm supply voltage, ground quality and bus termination before condemning the sensor module.
• Inspect the harness for heat damage and the connector for moisture and green corrosion.
• Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.

Quality, packaging and ordering 201141

BG 201141 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 24V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 51.15408-0015 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201141 replace OE 51.15408-0015?

Yes. BG 201141 is listed against 51.15408-0015, 5WK9 6618D and 5115408-0015 51.15408-0013 5115408-0013. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201141 fit?

Recorded coverage includes MAN. It is supplied as a direct-fit aftermarket nox sensors on 24V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201141.