NOx Sensor 4M0907807AJ

BG 201401 (OE 4M0907807AJ): function on the vehicle

NOx Sensor 4M0907807AJ is supplied by BEST GROWTH under part number 201401, cross-referenced to OE 4M0907807AJ, as a direct-fit aftermarket nox sensors. In service it measures nitrogen-oxide concentration and residual oxygen in the exhaust stream and reports both values to the aftertreatment controller over the vehicle data bus. Upstream and downstream readings together set DEF dosing quantity and score SCR conversion efficiency.

BG 201401 is built to the position defined by its OE application on a 12V electrical system in passenger car service on the platform from Volkswagen. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

The measuring cell is consumable. Soot loading, silicone contamination and repeated thermal shock all shorten its life, which is why a sensor can drift for months before it sets a hard code.

Fitment for Volkswagen and OE cross reference

BG 201401 replaces 1 OE reference: 4M0907807AJ. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201401 includes Volkswagen, typically on Passat 2.0L / A4 / S4 / A5 / S5 2012-2015. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Quote the number printed on your part with the engine code when you enquire; a single-reference part is the most common source of ordering errors when a platform received a mid-life update.

Symptoms that lead to replacing 4M0907807AJ

These complaints bring a vehicle in with the Volkswagen nox sensors under suspicion. None of them prove BG 201401 has failed on its own, which is why the checks below matter before a replacement is ordered.

• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running
• upstream and downstream values reading almost identically under load
• intermittent fault that clears after the engine cools and returns when hot

Checks before fitting BG 201401

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Read the sensor's own dew-point release time — a cell that never heats is a supply or module fault.
• Verify DEF concentration with a refractometer before blaming the measuring cell.
• Check for a pending software or parameter update for the sensor control module on that platform.
• After fitting, run the manufacturer's adaptation or relearn so stored efficiency counters reset.
• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.

Quality, packaging and ordering 201401

BG 201401 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 12V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 4M0907807AJ or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201401 replace OE 4M0907807AJ?

Yes. BG 201401 is listed against 4M0907807AJ. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201401 fit?

Recorded coverage includes Volkswagen. It is supplied as a direct-fit aftermarket nox sensors on 12V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201401.