NOx Sensor 2296799

BG 201486 (OE 2296799): function on the vehicle

NOx Sensor 2296799 is supplied by BEST GROWTH under part number 201486, cross-referenced to OE 2296799, as a direct-fit aftermarket nox sensors. In service it runs a heated zirconia measuring cell inside its own sensor control module, converts the raw cell current into a NOx value in ppm, and publishes it on the bus. The engine controller cannot calculate dosing quantity or conversion efficiency without a plausible signal from it.

BG 201486 is built to the position defined by its OE application on a 24V electrical system in truck service on platforms from IVECO and Scania. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Fitting position matters as much as the part number: upstream and downstream references often share a housing but carry different calibration data and cable lengths.

Fitment for IVECO and Scania and OE cross reference

BG 201486 replaces 5 OE references: 2296799, 2020691, 5WK9 6612F, 5WK9 6612D and 5WK9 6612D 5WK9 6612F, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201486 includes IVECO and Scania, typically on Stralis / Trakker Euro 5. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by 2296799 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing 2296799

These complaints bring a vehicle in with the IVECO and Scania nox sensors under suspicion. None of them prove BG 201486 has failed on its own, which is why the checks below matter before a replacement is ordered.

• SCR efficiency below threshold or NOx-signal-implausible fault codes
• DEF over-consumption with no visible leak
• torque derate or speed inducement with a full, in-spec DEF tank
• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up

Checks before fitting BG 201486

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.
• Read the sensor's own dew-point release time — a cell that never heats is a supply or module fault.
• Verify DEF concentration with a refractometer before blaming the measuring cell.
• Check for a pending software or parameter update for the sensor control module on that platform.
• After fitting, run the manufacturer's adaptation or relearn so stored efficiency counters reset.

Quality, packaging and ordering 201486

BG 201486 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 24V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 2296799 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201486 replace OE 2296799?

Yes. BG 201486 is listed against 2296799, 2020691, 5WK9 6612F, 5WK9 6612D and 5WK9 6612D 5WK9 6612F. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201486 fit?

Recorded coverage includes IVECO and Scania. It is supplied as a direct-fit aftermarket nox sensors on 24V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201486.