NOx Sensor 21567736

BG 201491 (OE 21567736): function on the vehicle

NOx Sensor 21567736 is supplied by BEST GROWTH under part number 201491, cross-referenced to OE 21567736, as a direct-fit aftermarket nox sensors. In service it runs a heated zirconia measuring cell inside its own sensor control module, converts the raw cell current into a NOx value in ppm, and publishes it on the bus. The engine controller cannot calculate dosing quantity or conversion efficiency without a plausible signal from it.

BG 201491 is built to the position defined by its OE application on a 24V electrical system in truck and construction equipment service on the platform from Volvo. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Because the sensor carries its own control module, most "sensor" faults are really bus, supply or ground faults at the connector — the electrical side is worth ten minutes before the part is ordered.

Fitment for Volvo and OE cross reference

BG 201491 replaces 2 OE references: 21567736 and 5WK9 6664E, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201491 includes Volvo, typically on FH / FM / FL / FE; A25F / A25G / A30F. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by 21567736 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing 21567736

These complaints bring a vehicle in with the Volvo nox sensors under suspicion. None of them prove BG 201491 has failed on its own, which is why the checks below matter before a replacement is ordered.

• torque derate or speed inducement with a full, in-spec DEF tank
• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running
• upstream and downstream values reading almost identically under load

Checks before fitting BG 201491

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• After fitting, run the manufacturer's adaptation or relearn so stored efficiency counters reset.
• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.
• Confirm supply voltage, ground quality and bus termination before condemning the sensor module.
• Inspect the harness for heat damage and the connector for moisture and green corrosion.
• Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.

Quality, packaging and ordering 201491

BG 201491 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 24V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 21567736 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201491 replace OE 21567736?

Yes. BG 201491 is listed against 21567736 and 5WK9 6664E. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201491 fit?

Recorded coverage includes Volvo. It is supplied as a direct-fit aftermarket nox sensors on 24V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201491.